Please log in
You must be logged in to send the contact request.
Manage stand orders
Select Option
CONTROLE MESURE SYSTEMES
6, rue des Lochés,
71100
Sevrey
France
France
Submit your contact details
Provide your contact details to the exhibitor. Optionally, you may also add a personal message.
Your name, phone number, and e-mail address are subject to the submission of personal data. Messe Düsseldorf GmbH expressly points out that for a data transmission into third countries, for which no adequacy decision of the EU-commission is on hand certifying an adequate level of protection of personal data, it is not ensured that there are appropriate safeguards for the protection of personal data on hand.
An error has occurred
Please check your internet connection or try again later.
Message has been sent
Your message to the exhibitor was sent successfully.
This company is main exhibitor of
Location
Hall map
Fairground map
Our range of products
Product categories
- 05 Testing technology, sensor technology and quality assurance for the tube and pipe industry
- 05.01 Materials testing
- 05.01.02 Equipment for non-destructive materials testing
Equipment for non-destructive materials testing
- 05 Testing technology, sensor technology and quality assurance for the tube and pipe industry
- 05.03 Product testing
- 05.03.03 Eddy current and magnetic powder testing equipment
Eddy current and magnetic powder testing equipment
- 05 Testing technology, sensor technology and quality assurance for the tube and pipe industry
- 05.03 Product testing
- 05.03.04 Ultrasonic test equipment
Ultrasonic test equipment
Our products
Product category: Eddy current and magnetic powder testing equipment
Eddy current rotating head RotoETscan
is intended for longitudinal defects detection
CMS is offering a large range of rotating heads, for longitudinal defects detection in wires, tubes and, bars
With six different sizes (products diameters from 1 up to 220 mm), CMS rotating heads are adaptable to any production line.
Can be associated with inserts and input and output centering devices, for guiding the product on the rotating head (from 4 mm product diameter)
CMS is offering a large range of rotating heads, for longitudinal defects detection in wires, tubes and, bars
With six different sizes (products diameters from 1 up to 220 mm), CMS rotating heads are adaptable to any production line.
Can be associated with inserts and input and output centering devices, for guiding the product on the rotating head (from 4 mm product diameter)
Product category: Eddy current and magnetic powder testing equipment
Eddy current magnetizing units
allow short and transverse defects detection
Large range of monobloc and opening magnetizing units, for ferromagnetic products such as tubes, bars, wires, and pipes inspection for products from 1 up to 230 mm diameter. Inserts, guide sleeves and adaptators allow to adapt the size of the magnetizing unit to the product range. Opening version is intended for wires inspection to avoid cutting product.
Large range of monobloc and opening magnetizing units, for ferromagnetic products such as tubes, bars, wires, and pipes inspection for products from 1 up to 230 mm diameter. Inserts, guide sleeves and adaptators allow to adapt the size of the magnetizing unit to the product range. Opening version is intended for wires inspection to avoid cutting product.
Product category: Eddy current and magnetic powder testing equipment
Eddy current sectorial magnetizing units
are developed for weld inspection
Sectorial magnetizing unit is intended for small defects detection in tubes and bars weld area such as holes or cracks, open or disrupted weld.
It can inspect products from 5 up to 300mm diameter.
It allows detecting also long defects, essentially for rolled welded tubes, and inspecting multiple lines simultaneously using one Eddy Current equipment (up to 4 lines).
An other kind of application can be for rails inspection to inspect the head and the base of the rail
Sectorial magnetizing unit is intended for small defects detection in tubes and bars weld area such as holes or cracks, open or disrupted weld.
It can inspect products from 5 up to 300mm diameter.
It allows detecting also long defects, essentially for rolled welded tubes, and inspecting multiple lines simultaneously using one Eddy Current equipment (up to 4 lines).
An other kind of application can be for rails inspection to inspect the head and the base of the rail
About us
Company portrait
Controle Mesure Systemes SAS (CMS) is a leading manufacturer of Non-destructive Testing equipment, specialized in Eddy Current and Ultrasonic inspections.
We handle the design, conception, and development of every component of our systems (mechanical, electrical, software). Our goal is to provide high quality turnkey solutions to improve the safety, efficiency and profitability of our customers.
Our skilled and multidisciplinary engineering team is constantly researching, investing and developing new technologies to meet or exceed our customer’s needs. Additionally, we can create and test any kind of probes and coils in our in-house laboratory.
In December 2020, its American division CMS Inc opened in New York, NY.
We are proud to work with some of the most prestigious manufacturers in Aerospace, Nuclear, Metal, Automotive & Rail, and many more industries. Our know-how, expertise, and constant equipment improvement are essential to successfully handle the increasingly challenging demands of our customers.
Our extensive network of agents allows us to quickly assist you in any situation. We are present in Europe (Italy, Spain, Czech Republic, Russia, Turkey, …), Asia (China, Korea, India, Thailand, …), South America (Brazil, Mexico, …) and the United States of America.
Visit the website www.cmseddyscan.com or contact us at contactcms@cmseddyscan.com to discover all our products, accessories, software, special machinery and turnkey systems.